Garter springs are coiled springs with their ends joined to form a ring, so they apply even radial force around a shaft, seal, or housing. When the garter spring in your seal has failed, has gone obsolete, or has to survive corrosive or high-temperature service the original alloy was never meant for, Coiling Technologies builds custom garter springs to your drawing, specification, or sample.
As a garter spring manufacturer that works only to order, we engineer and build every spring in Houston, Texas. We wind garter springs in stainless steel, in nickel alloys such as Inconel, Hastelloy C-276, and Monel 400, and in other specialty spring materials. Our engineers review each request against the load, temperature, and media the spring will see in service.
What a Garter Spring Does in a Seal or Assembly
A garter spring works through radial force. Because the force acts around the full circumference of the ring, it keeps contact even as a shaft runs out of round, a seal lip wears, or parts expand and contract with temperature. Garter springs come in two configurations:
- Extension garter springs: close-wound coils that pull inward toward the center of the ring. This is the oil seal spring that holds a lip seal against a rotating shaft.
- Compression garter springs: spaced coils that push outward from the center, used inside a bore or housing to hold a component against an outer surface.
Typical applications include radial lip and shaft seals, oil seals, pump and compressor seals, piston and rod seals, packers and downhole tools, electrical connectors, and shielding rings.
Garter Spring Alloys for Corrosive and High-Temperature Service
The material often decides how long a seal lasts. A carbon steel garter spring that performs well in clean, lubricated service can corrode quickly in sour gas, seawater, or chemical processing. That is why many of the garter springs we are asked to quote are material upgrades.
- Stainless steel (302, 316, 17-7 PH): General corrosion resistance for water, process fluids, and industrial seals. See our stainless steel springs.
- Monel 400: Resistance to seawater and many acids, which is why Monel 400 springs are often specified for marine, naval, and offshore equipment.
- Hastelloy C-276: Resistance to chlorides, sulfuric and hydrochloric acids, and sour service, making Hastelloy C-276 springs a common choice in chemical processing and oil and gas.
- Inconel 600 and X-750: Strength and relaxation resistance at high temperature, the reason Inconel springs go into turbines, valves, and downhole tools.
- Beryllium copper: Electrical conductivity and non-magnetic behavior, so beryllium copper springs suit contact and shielding rings.
- Carbon spring steels and music wire: A cost-effective choice for oil seals in clean, lubricated, moderate temperature service.
If your print calls out a material specification, we build to it. If it does not, tell us the media, temperature, and pressure, and our spring design services team will recommend an alloy.
What We Need to Quote a Garter Spring
Send as much of the following as you have. A drawing or a physical sample is enough to get started.
- Ring inside diameter (ID), free and installed
- Coil outside diameter (OD) and wire diameter
- Free length of the spring before joining, or the installed circumference
- Material or material specification
- End connection type, as shown on your drawing or sample
- Installed radial load or tension, if known
- Operating temperature, media, and pressure
- Quantity
- Drawing, seal part number, photo, or physical sample
Wire diameter, ring size, and end connection are set by your drawing or sample. Our quote form accepts drawing and photo uploads, so you can attach your print or pictures of the spring with your request.
Garter Springs vs. Canted Coil Springs
Both springs sit in seal grooves and deliver radial force, but they behave differently. A garter spring is a conventional helical coil joined into a ring, and its force rises in proportion to deflection like any extension or compression spring. A canted coil spring has coils wound at an angle. That gives a relatively flat force over a wide deflection range, plus multi-point contact for conductivity and EMI shielding.
- Choose a garter spring for standard radial lip and oil seal designs, or when you are replacing an existing garter spring and want the same fit and force.
- Choose a canted coil spring when the seal or connector needs consistent force across a wide tolerance range, or electrical contact around a joint.
We manufacture both types, so our engineers can tell you which one suits your groove and service conditions.
Replacing a Failed or Obsolete Garter Spring
Many garter spring requests come from maintenance and sourcing teams holding a worn seal with no drawing, often from equipment whose original supplier no longer makes the part. Send us the spring or the seal that holds it. We document the wire size, coil and ring dimensions, and end connection. Then we build a prototype for your approval before production, the same path outlined on our spring prototyping page.
Through our spring reverse engineering process, we can match the original spring exactly or build the replacement in an alloy better suited to your service. All work is performed under our ISO 9001:2015 certified quality management system.
Where Our Garter Springs Are Used
- Oil and gas: Seals in downhole tools, pumps, compressors, and wellhead equipment. See oil and gas and petrochemical springs.
- Military and defense: Shaft seals and connectors in vehicles, ships, and weapons systems. See military springs.
- Valves and flow control: Stem and rotary seals in industrial valve assemblies.
- Subsea and marine: Seals exposed to seawater and pressure in deep-sea equipment.
- Pumps and rotating equipment: Oil seals on motors, gearboxes, and pump shafts.
Request a Quote for Custom Garter Springs
Tell us what the spring does, what it is made of today, and what it needs to survive. Request A Quote and upload your drawing or photos, and our engineers will review your garter spring requirements. If you only have a sample, note it on the form, and our team will contact you about next steps.
Garter Springs FAQs
What is a garter spring?
A garter spring is a helical coil spring with its ends joined to form a ring. Extension garter springs pull inward and hold seal lips against shafts, while compression garter springs push outward against a bore or housing.
What is an oil seal spring?
An oil seal spring is an extension garter spring fitted in the groove of a radial lip seal. It keeps the seal lip in contact with the rotating shaft as the elastomer ages and wears, which helps the seal retain oil and keep contaminants out.
What materials can garter springs be made from?
Common materials include carbon spring steel and music wire, stainless steels such as 302, 316, and 17-7 PH, nickel alloys including Inconel, Hastelloy C-276, and Monel 400, and beryllium copper. Coiling Technologies selects the alloy from the media, temperature, and pressure the spring will see, or builds to the material specification on your print.
Can you make a garter spring from a sample?
Yes. Send the spring or the seal it came from, along with any known dimensions and application details. Our team documents the sample and builds a prototype for your approval before production.
How do the ends of a garter spring connect?
Garter springs are commonly joined with hook and eye ends, a tapered end that screws into the opposite end, or a separate connector. The connection for your spring is set by your drawing or sample.
What is the difference between a garter spring and a canted coil spring?
A garter spring is a conventional helical coil joined into a ring, with force that rises in proportion to deflection. A canted coil spring has angled coils that deliver a relatively flat force across a wide deflection range and multi-point contact for conductivity and EMI shielding.



