A spring can meet every dimension on the drawing and still fail early if the finish is wrong for the material or the environment. Stainless springs that pick up free iron during manufacturing can rust in service. Carbon steel springs left bare corrode. High-strength springs plated without proper relief can crack under load. Coiling Technologies supplies passivated springs and plated springs finished to the callout on your print, so the finish protects the spring instead of creating a new failure point.
Every spring we build is custom-made to order. Tell us the finish your print calls for, or the environment the spring will see, and our engineers will confirm the right combination of material and finish before production begins.
Passivated Springs: What Passivation Does and Which Springs Need It
Passivation is a chemical treatment for stainless steel. An acid solution removes free iron and other surface contaminants left from wire drawing, coiling, grinding, and handling. That allows a continuous chromium oxide layer, the passive film, to form across the surface. The passive film is what gives stainless steel its corrosion resistance, and contamination left on the surface can become a starting point for rust and pitting.
Passivation of springs does not add a coating or noticeably change dimensions, which makes it well suited to close-tolerance parts. Stainless steel spring passivation is commonly specified for:
- 302 and 304 stainless springs: general corrosion resistance in industrial, food, and medical equipment. See our stainless steel springs.
- 316 stainless springs: chloride and marine exposure, where molybdenum adds pitting resistance. See our 316 stainless steel springs.
- 17-7 PH springs: precipitation hardening stainless for higher strength and temperature. See our 17-7 PH springs.
- 17-4 PH springs: high strength stainless components where corrosion resistance is still required. See our 17-4 PH springs.
When your print calls out passivation, we supply the springs passivated to your specified callout.
Plated Springs: Zinc, Tin, Copper, and Electroless Nickel
Carbon and alloy steel springs do not form a passive film, so they rely on a coating for corrosion protection. Plated springs are supplied to the plating callout on your print:
- Zinc plated springs: zinc corrodes sacrificially to protect the steel underneath. It is a common, economical finish for carbon steel springs in general industrial service.
- Nickel plated springs (electroless nickel): electroless nickel deposits without electric current, so it builds an even layer inside coils and on complex shapes. It is used for wear and corrosion resistance on springs with tight geometry.
- Tin plated springs: used where solderability or electrical contact matters, such as springs in electrical assemblies.
- Copper plated springs: used for conductivity, or as an underlayer beneath another finish.
Zinc and iron phosphate coatings are applied in house and can also serve as a base for paint or powder.
Reading Your Print: Finish Callouts and What They Mean
Prints often call out a finish by specification number rather than by name. This table lists common callouts seen on spring drawings and how they are typically used. Each is a customer-specified requirement that springs can be supplied to, not a certification.
| Finish | Common print callout | Typical spring use |
|---|---|---|
| Passivation | ASTM A967, AMS 2700 | Stainless springs (302, 316, 17-4 PH, 17-7 PH) |
| Passivation (legacy) | QQ-P-35, AMS-QQ-P-35 | Older prints for stainless springs; newer prints often reference ASTM A967 or AMS 2700 |
| Zinc plating | ASTM B633 | Carbon and alloy steel springs in general service |
| Electroless nickel | ASTM B733 | Springs with complex geometry needing even coverage |
| Tin or copper plating | As specified on the print | Electrical contact, solderability or underlayers |
| Salt spray testing | ASTM B117 | Verification of corrosion performance when the print requires it |
If your drawing references a specification not listed here, include it with your request and our engineers will review it.
Plating High-Strength Steel Springs: Hydrogen Embrittlement and Bake Relief
Hydrogen embrittlement is a plating problem. Acid cleaning and plating can introduce atomic hydrogen into high-strength steel. In a spring hardened to a high strength level, that hydrogen can cause delayed cracking under sustained load, sometimes days after installation.
The standard safeguard is bake relief: a controlled thermal cycle after plating that drives hydrogen out of the steel before it can cause damage. Plating specifications for high-strength steel typically require it, and your print should state the bake requirement along with the plating callout. Springs plated to your callout are supplied with the relief your specification requires.
When Powder Coating Is the Better Finish for a Spring
For carbon and alloy steel springs in outdoor or heavy-duty service, powder coating often makes more sense than plating. Powder coating involves no plating bath, so it carries no hydrogen embrittlement risk. It also applies a thicker protective film that stands up to handling and coil contact. Our powder coating is performed in-house over an iron phosphate pretreatment. If your print calls for plating mainly for corrosion protection, ask our engineers whether powder coating would serve the application better.
How Finishing Fits With Heat Treating and Shot Peening
The order of operations affects how a finished spring performs:
- Heat treating establishes the spring's strength and hardness before any finish is applied.
- Shot peening adds compressive stress to the surface for fatigue life. On stainless springs, passivation after peening removes iron particles that peening media can leave on the surface.
- Inspection, including non-destructive testing when the print requires it, confirms the spring is sound before the finish goes on.
- Plating or passivation is applied to your callout, followed by bake relief where plating on high-strength steel requires it.
Because heat treating, shot peening, powder coating, and phosphating all run in our Houston facility under an ISO 9001:2015 certified quality management system, the finishing sequence is planned with the rest of the spring rather than added at the end.
Request a Quote for Passivated or Plated Springs
Attach your print with the finish callout, and tell us the material and operating environment. Request A Quote, and our engineers will review the spring and the finish together.
Passivated and Plated Springs FAQs
What is a passivated spring?
A passivated spring is a stainless steel spring that has been treated with an acid solution to remove free iron and surface contaminants. That allows a uniform chromium oxide layer to form and restores the corrosion resistance of the stainless steel.
Does passivation change the dimensions of a spring?
No. Passivation removes contaminants from the surface rather than adding a coating, so it does not noticeably change spring dimensions.
Can carbon steel springs be passivated?
No. Passivation applies to stainless steels and some other corrosion-resistant alloys. Carbon and alloy steel springs need a coating such as zinc plating, electroless nickel, phosphate, or powder coating for corrosion protection.
What is the difference between ASTM A967 and QQ-P-35?
Both are passivation specifications for stainless steel. QQ-P-35 is a legacy federal specification that still appears on older prints, while newer prints often reference ASTM A967 or AMS 2700.
Why do plated springs need bake relief?
Plating can introduce hydrogen into high-strength steel, which can cause delayed cracking under load. Bake relief is a thermal cycle after plating that removes the hydrogen before it can damage the spring.
Is powder coating better than plating for springs?
For carbon and alloy steel springs in outdoor or heavy-duty service, powder coating is often the better choice because it carries no hydrogen embrittlement risk and applies a thicker protective film. Plating is preferred when the print requires a thin, uniform metallic finish, conductivity, or solderability.



